Intel® Xeon® E5-2600Lv3/v4 series processor based on PICMG 1.3 SHB with DDR4 REG SDRAM, VGA, Dual Gigabit Ethernet, and SATA/USB
ROBO-8122VG2R is based on Intel® C612 chipset and dual Xeon® processors. It’s a server grade SHB. Build with high conputing power and PCI express expension support, it’s suitable for Military, industrial automation, networking, Medical and Digital Signage applications.
Support Intell® 6C~12C Xeon® processors with LGA 2011 package
Del i ver s up to 256GB DDR4 ECC registered memory assured the computer reliability and benefited the data swapping process
Adopt ASPEDD AST1400 graphic engine offers solid 2D performance by VGA port
High speed Gigabit Ethernet based on PCI express x 1 interface
Flexible PCI Express configuration on backplane up to total 36 lanes
Processor ．Intel® 6C~12C Xeon® E5-2600Lv3/v4 series processor (50~75W) with 15~30MB Cache in LGA2011 package (support up to 75W per CPU)
．Intel® QPI transfer rates: 6.4, 8 and 9.6GT/s (depends on CPU sku)
．DMI x4 Link: 5 GT/s
．Supports Intel® Hyper-Threading, Virtualization Technology (VT-x), and QuickPath Technology
Chipset Intel® C612 PCH
BIOS AMI uFEI BIOS (SPI ROM)
Memory ．Supports up to 256GB DDR4 2133/1866 SDRAM on Eight 288-pin DIMM sockets
．Supports Register
Storage Devices ．4x SATAIII drives (Dual ports via Backplane)
．RAID 0, 1
Watchdog Timer Programmable via S/W from 0.5 sec. to 254.5 sec.
Hardware Monitoring System monitor(Voltage,Fan Speed and Temperature)
Expansion Interface ．From per CPU: 1x PCI Express x16 or 2x PCI Express x8 or 1x PCI Express x8 + 2x PCI Express x4 by different bios support (Gen3 up to 8.0 GT/s)
．From PCH: 1x PCI Express x4 or 4x PCI Express x1 by different bios support (Gen 3 up to 8.0 GT/s)
Super I/O(Embedded Controller) ITE IT8772E
Audio N/A
Ethernet ．On-board Intel® WGI217LM + WGI210AT gigabit ethernet controller
．Dual 10BASE-T / 100BASE-TX / 1000BASE-T Ethernet
．PCI Express x1 interface based on gigabit ethernet
．Single RJ-45 connector with two LED indicators for WGI217LM on bracket, the other port route to gold finger section C on BP for WGI210AT
Serial Port 2x Tx/Rx signal route to gold finger section C on BP (4 pins)
USB ．4x USB 2.0 ports ( through backplane)
．480Mb/s bus capable of high-speed/full-speed/low-speed data ranges
．2x USB 3.0 ports on bracket
．5Gbps bus capable of high-speed/ full-speed/low-speed data ranges
Keynoard & Mouse ．2x USB 3.0 ports on bracket dedicated to keyboard & mouse
GPIO N/A
Graphic Controller ASPEED AST1400
Display Interface CRT on bracket: Resolution up to 1920x1200@60Hz
Dimension 338.5mm(L) x 126.39mm(W), 13.33"(L) x 4.98"(W)
Power Supply Typical: +12V, +5V
-Support ATX mode
Environment Operatin Temperature:0°C~55°C (for 75W CPU limitation)
Storage Temperature:-20°C~80°C
Relative Humidity:5~90%,non-condensing
Thermal Solution depends on chassis design and system fan selection
MTBF Over 100,000 hours at 40°C
Non-standard Golden Finger definition ．Section A/B: PICMG 1.3 Standard PCI Express definition, total 20 lanes
Section D: PCIe x 16 from 2nd CPU(Dedicated backplane for ROBO-8122VG2R)
.jpg "Bus Passifs")
